Towards the bottom of the logic board, 3G owners will only see one cable to the left labeled 4. 3GS users will see two cables (one on each side of the dock connector) labeled 4 and 7. 3G users will just pop up the number 4 cable while 3GS owners will need to pop up both the number 4 and 7 cables.
If your iPhone 3G or iPhone 3GS is no longer holding a charge, and always running out of laptop battery, replacing the extended life sony laptop battery is a moderate level DIY repair. If you’ve got the right tools and parts, it shouldn’t be too difficult to swap out that old dell laptop battery for a brand new one on your own. It’ll take a little bit of patience and about 30 minutes of your time. Disclaimer: As with any repair, TiPb nor PXLFIX can be held responsible for any damage you may do to your device. It’s also worth considering that opening up your device to perform any repair or modification can and will void your acer battery warranty. If you don’t feel comfortable opening your device, don’t. Use extreme care and caution when performing a repair on any device.
What you need for a DIY iPhone 3G/3GS compaq laptop battery swap PXLFIX recommends using only quality and genuine parts from a reputable supplier like eTech Parts. They have quality parts, tools, and much more for all your repair needs.
Gently lift up your digitizer enough to have a clear view of the 3 cables in the top right of your iPhone. With your plastic spudger or pry tool, you’ll need to pry up the first two cables that attach the digitizer and LCD. They should be labeled with orange stickers numbered 1 and 2. Simply pop them off the logic board gently. Underneath these cables you’ll see one other labeled as cable 3. This one is a bit trickier as it is clipped down. You’ll need to gently pop up the clasp holding it into the fastener. It is a tiny white clip. Simply pop it upwards and the number 3 cable should then slide right out. Remove the digitizer & LCD assembly and set it aside. Remove your SIM card Using your SIM tool or a paperclip, either works, remove your SIM card and tray from your device.
Remove the digitizer & LCD assembly This part can be a bit tricky so please do this with extreme care so you don’t tear any cables during the process. I highly recommend using the suction cup method unless your screen is cracked above the home button for some reason and you can’t get a proper seal with the suction cup. Suction cup method (recommended): The easiest way to remove the digitizer assembly is by using a suction cup.
Unclip cables from the logic board Towards the top left of the logic board, use your pry tool to pop up the two cables labeled 5 and 6.
Position the suction cup on the screen directly above the home button. Using your other hand, hold down the frame while gently pulling up on the suction cup. The goal is to get the bottom of the digitizer loose. Do not pull directly up. There are 3 cables attached in the top right of your iPhone. You do not want to tear these. Just pull up until the bottom of the assembly pops out. After you have the bottom up you can remove the suction cup. Spudger/razor blade method (only use this method as a secondary method): ONLY use this method if your screen is cracked above the home button. If this is the case, you’ll need to use a razor blade or spudger in order to remove it. And while you’re at it, replace that broken screen! Starting in the bottom left hand corner, insert a plastic spudger and gently pry up. Once the first side is starting to pop up, do the same on the bottom right side. Run your pry tool along the bottom of the device in order to pop up the bottom of the assembly. Take special care around the home button area. Remove the cables that attach the digitizer assembly to the logic board: Once you have the bottom of your digitizer assembly popped up we can remove the cables attaching it to the logic board.
.
A sad iPhone 3G or 3GS A new laptop battery A #00 Phillips screwdriver A suction cup A pry tool or spudger Sim removal tool or paperclip laptop battery off your iPhone Before performing any repair, always laptop battery off your device before removing any screws or parts.
Remove the dock connector screws Using your #00 Phillips screwdriver, remove the 2 screws located on each side of the dock connector.