Reassemble the digitizer 1. Begin with the number 3 cable that clips down. Getting it seated can be a bit tricky. Use a plastic spudger to guide it in the opening if needed. Then push back down the clip that holds it in place.

Replace the logic board screws Replace the eight screws your removed earlier that secure the logic board. Just make sure you replace the metal clip over the camera before replacing the screw that holds it in place.

Insert the new sony laptop battery Most ibm laptop battery will come with adhesive already on them. Simply remove the backing from the adhesive and place the acer battery satellite a105 mitac laptop battery in the device taking care not to trap any loose cables underneath it. Push down firmly to make sure the adhesive stays in place.

2. Next push down the number 1 and 2 cables onto the logic board.

3. Notice the screw holding the camera in place has a metal bracket underneath it. Just take care not to lose this as you’ll need to put it back during reassembly.

Reposition and snap down your camera Once the logic board is positioned right, you can reposition and snap down your camera again.

Replace the logic board Make sure there are no cables in the way. I typically tuck the number 4 cable into the frame (refer to video) so it does not get stuck underneath the logic board. Start by positioning the top of the logic board below where the SIM tray sits and start sliding it upwards into place. Once the top is in place, you can place the bottom of the logic board into its place. Just make sure no cables are stuck underneath the logic board where they should be on top. asus battery pa3356u-3bas extended mitac laptop battery brand new 4400mAh Only AU $58.31 mitac battery satellite a205 extended gateway laptop battery brand new 4400mAh Only AU $60.07 toshiba battery probook 4510s extended life laptop battery Li-ion, 4400mAh 10.8V only AU $53.85 Insert your SIM card and tray The easiest way to make sure the logic board is in place is to replace your SIM card tray at this point. If it slides in easily, you’re right on track. Don’t force it if it doesn’t want to go in. That means you don’t have the logic board lined up correctly. Remove it and try again. The SIM tray will also help keep the logic board in place as you replace screws in the logic board.

2. Towards the bottom of the logic board, 3G owners will only see one cable to the left labeled 4. 3GS users will see two cables (one on each side of the dock connector) labeled 4 and 7. 3G users will reconnect the number 4 cable while 3GS owners will need to reconnect both the number 4 and 7 cables.

.

2. Make sure you place the screws in an order you will remember. They are different sizes in some instances so you’ll need to make sure you put them back in the correct order.

3. To snap the digitizer assembly back in place, start at the top and make sure it is lined up. Once the top is pushed down and flush, snap the bottom into place on each side of the home button.

5. Insert your pry tool in the space between the dock connector and logic board and gently pry upward to loosen the logic board.

1. Remove the 8 screws outlined in the video that hold the logic board in place. One of the screws is under a Do not remove sticker at the bottom right by the dock connector. Obviously you’ll have to remove the sticker to get to it.

And… done! If you followed all the steps above correctly you should be able to laptop battery on your phone and be on your way! I recommend you drain the FIC 21-91081-00 mitac laptop battery completely and do one full charge. You also may notice you’ll need to reset the time and date on your device. mitac laptop battery pulls tend to reset the clock.

Remove the old ibm battery pavilion dv6 mitac laptop battery There is nothing holding the toshiba laptop battery down but adhesive. Gently use your pry tool to loosen the ibm laptop battery pack from the back of the device. Run it along the sides and gently pry up taking care not to bend or damage the dell battery elitebook 8530w extended sony laptop battery. They are secured with quite a bit of adhesive so you may have to use a little bit of force to remove it. Just take care not to bend the casing either.

4. Replace the two dock connector screws.

4. Gently pop your camera up with your spudger or pry tool.

6. Gently grab the bottom of the logic board and slide it out downwards to remove it.

Reconnect cables to the logic board 1. Towards the top left of the logic board, reconnect the two cables labeled 5 and 6.